Methane hydrate is widely distributed in the pores of marine sediments or permafrost soils, contributing to their mechanical properties. Yet the tensile properties of the hydrate at pore scales remain almost completely unknown, notably the influence of grain size on its own cohesion. Here we grow thin films of the hydrate in glass capillaries. Using a novel, contactless thermal method to apply stress, and video microscopy to observe the strain, we estimate the tensile elastic modulus and strength. Ductile and brittle characteristics are both found, dependent on sample thickness and texture, which are controlled by supercooling with respect to the dissociation temperature and by ageing. Relating the data to the literature suggests the cohesive strength of methane hydrate was so far significantly overestimated.

There is an increasing interest in developing porous metals or metallic foams for functional and structural applications. The study of the physical and mechanical properties of porous metals is very important and helpful for their application. In this paper, a novel sintered multilayer wire mesh porous plate material (WMPPs) with a thickness of 0.5 mm-3 mm and a porosity of 10-35% was prepared by winding, pressing, rolling, and subsequently vacuum sintering them. The pore size and total size distribution in the as-prepared samples were investigated using the bubble point method. The uniaxial tensile behavior of the WMPPs was investigated in terms of the sintering temperature, porosity, wire diameter, and manufacturing technology. The deformation process and the failure mechanism under the tensile press was also discussed based on the appearance of the fractures (SEM figures). The results indicated that the pore size and total size distribution were closely related to the raw material used and the sintering temperature. For the WMPPs prepared by the wire mesh, the pore structures were inerratic and the vast majority of pore size was less than 10 μm. On the other hand, for the WMPPs that were prepared by wire mesh and powder, the pore structures were irregular and the pore size ranged from 0 μm-50 μm. The experimental data showed that the tensile strength of WMPPs is much higher than any other porous metals or metallic foams. Higher sintering temperatures led to coarser joints between wires and resulted in higher tensile strength. The sintering temperature decreased from 1330 °C to 1130 °C and the tensile strength decreased from 296 MPa to 164 MPa. Lower porosity means that there are more metallurgical joints and metallic frameworks resisting deformation per unit volume. Therefore, lower porosities exhibit higher tensile strength. An increase of porosity from 17.14% to 32.5% led to the decrease of the tensile strength by 90 MPa. The coarser wires led to a bigger contact area between the interconnecting wires, resulting in a stronger sintering neck that exhibited higher tensile strength. The wire diameter increased from 81 μm to 122 μm and the tensile strength increased from 296 MPa to 362 MPa. The fracture morphology showed that the wires experience necking deformation and ductile fracture.

The tensile deformation and fracture behavior of a particular semi-equiaxed microstructure (S-EM) in a near alpha titanium alloy TA19 are investigated by an in situ method. In the S-EM, the thin β lamellae grow through the equiaxed αp phase (αp), and the original αp/βtrans interface in the bimodal microstructure largely disappears, forming a blurry interface between the semi-equiaxed αp phase (equiaxed αp phase that is grew through by the thin β lamellae) and the transformed β microstructure (βtrans). The formation of dense slip bands inside the semi-equiaxed αp phase in the S-EM is inhibited by the thin β lamellae during the tensile deformation. The special characteristics of the S-EM reduce the stress concentration at the interface, and the crack initiation probability in the blurry semi-αp/βtrans interface decreased compared to the distinct αp/βtrans interface in a conventional equiaxed microstructure (EM). Moreover, the ultimate tensile strength of the S-EM is higher than that of the EM with a slight loss of plasticity.

Mg-9Al-1Si-1SiC composites with various initial microstructures prior to equal channel angular pressing (ECAP) were obtained by different pre-treatments (without and with homogenization treatment), and the resultant grain size, second phase and tensile properties of ECAPed composites were reported. The ECAPed composite with homogenization treatment (HT) exhibited finer grain size, higher fraction of dynamically recrystallized (DRXed) grains, weaker texture intensity, as well as the presence of dynamic precipitated Mg17Al12 phase compared to that without HT. Besides, the morphology of pre-existing Mg₂Si changed from massive-like to needle-like in the ECAPed composite with HT. Room-temperature tensile test results showed that ultimate tensile strength (UTS), yield strength (YS), and elongation (El) of ECAPed composites with HT were 16.1%, 23%, and 27.3% larger than that without HT, respectively.

This article investigates the tensile and creep behaviors of the Ti-22Al-25Nb (at.%) alloy with equiaxed microstructure. The experimental results show that the equiaxed microstructures are formed by isothermal forging in the α₂ + B2 + O phase region, and then heat treating in α₂ + B2 + O and B2 + O phase regions. The equiaxed particles are determined by isothermal forging and solution heat treating, and the acicular O phase is obtained by adjusting the aging temperature. The strengths of the alloy are sensitive to the thickness of the secondary acicular O phase. Increase in aging temperature improves strength and reduces the ductility. Deformation of the alloy mainly depends on the volume fraction and deformability of the B2 phase. During the high-temperature tensile deformation, the flow stress decreases with the increasing deformation temperature and increases with the increasing strain rate. The microstructure obtained by higher aging temperature (HT-840) has better creep resistance, due to the coarsening of the secondary acicular O phase.

For many patients, rectal catheters are an effective means to manage bowel incontinence. Unfortunately, the incidence of catheter leakage in these patients remains troublingly high. Matching the mechanical properties of the catheter and the surrounding tissue may improve the catheter seal and reduce leakage. However, little data is available on the mechanical properties of colorectal tissue. Therefore, our group examined the mechanical properties of colorectal tissue obtained from both a common animal model and humans. Uniaxial tension tests were performed to determine the effects of location, orientation, and species (porcine and human) on bowel tissue tensile mechanical properties. Bowel tissue ultimate strength, elongation at failure, and elastic modulus were derived from these tests and statistically analyzed. Ultimate tensile strength (0.58 MPa, 0.87 MPa), elongation at failure (113.19%, 62.81%), and elastic modulus (1.83 MPa, 5.18 MPa) for porcine and human samples respectively exhibited significant differences based on species. Generally, human tissues were stronger and less compliant than their porcine counterparts. Furthermore, harvest site location and testing orientation significantly affected several mechanical properties in porcine derived tissues, but very few in human tissues. The data suggests that porcine colorectal tissue does not accurately model human colorectal tissue mechanical properties. Ultimately, the tensile properties reported herein may be used to help guide the design of next generation rectal catheters with tissue mimetic properties, as well as aid in the development of physical and computer based bowel models.

The human temporal muscle fascia (TMF) is used frequently as a graft material for duraplasty. Encompassing biomechanical analyses of TMF are lacking, impeding a well-grounded biomechanical comparison of the TMF to other graft materials used for duraplasty, including the dura mater itself. In this study, we investigated the biomechanical properties of 74 human TMF samples in comparison to an age-matched group of dura mater samples. The TMF showed an elastic modulus of 36 ± 19 MPa, an ultimate tensile strength of 3.6 ± 1.7 MPa, a maximum force of 16 ± 8 N, a maximum strain of 13 ± 4% and a strain at failure of 17 ± 6%. Post-mortem interval correlated weakly with elastic modulus (r = 0.255, p = 0.048) and the strain at failure (r =  - 0.306, p = 0.022) for TMF. The age of the donors did not reveal significant correlations to the TMF mechanical parameters. Compared to the dura mater, the here investigated TMF showed a significantly lower elastic modulus and ultimate tensile strength, but a larger strain at failure. The human TMF with a post-mortem interval of up to 146 h may be considered a mechanically suitable graft material for duraplasty when stored at a temperature of 4 °C.

Abrasions and pressure ulcers on the oral mucosa are most often caused by excessive pressure or incorrect fitting of the denture. The use of soft relining materials can eliminate pain sensations and improve patient comfort. The main functional feature of soft elastomeric materials is the ability to discharge loads from the tissues of the mucosa. (1) Background: The aim of the work was a comparative laboratory study of ten materials used for the soft lining of acrylic dentures. (2) Methods: There were materials based on acrylates (Vertex Soft, Villacryl Soft, Flexacryl Soft) and silicones (Sofreliner Tough Medium, Sofreliner Tough Medium, Ufi Gel SC, GC Reline Soft, Elite Soft Relining, Molloplast). Laboratory tests include the analysis of the tensile bond strength between the relining material and the acrylic plate of the prosthesis. The tests were conducted taking into account 90-day term aging in the distilled water environment based on the methodology presented in the European Standard ISO 10139-2. (3) Results: After three months of observation, the highest strength of the joint was characterized by Flexacryl Soft acrylic, for which the average value was 2.5 MPa. The lowest average value of 0.89 MPa was recorded for the GC Reline Soft silicone material. Over time, an increase in the value of the strength of the combination of acrylic materials and a decrease in these values in the case of silicone materials was observed. (4) Conclusion: Each of the tested silicone materials showed all three types of damage, from adhesive to mixed to cohesive. All acrylic-based materials showed an adhesive type of failure. Time did not affect the type of destruction.

The amount of microdamage in bone tissue impairs mechanical performance and may act as a stimulus for bone remodeling. Here we determine how loading mode (tension vs. compression) and microstructure (trabecular microarchitecture, local trabecular thickness, and presence of resorption cavities) influence the number and volume of microdamage sites generated in cancellous bone following a single overload. Twenty paired cylindrical specimens of human vertebral cancellous bone from 10 donors (47–78 years) were mechanically loaded to apparent yield in either compression or tension, and imaged in three dimensions for microarchitecture and microdamage (voxel size 0.7×0.7×5.0 μm3). We found that the overall proportion of damaged tissue was greater (p=0.01) for apparent tension loading (3.9±2.4%, mean±SD) than for apparent compression loading (1.9±1.3%). Individual microdamage sites generated in tension were larger in volume (p<0.001) but not more numerous (p=0.64) than sites in compression. For both loading modes, the proportion of damaged tissue varied more across donors than with bone volume fraction, traditional measures of microarchitecture (trabecular thickness, trabecular separation, etc.), apparent Young׳s modulus, or strength. Microdamage tended to occur in regions of greater trabecular thickness but not near observable resorption cavities. Taken together, these findings indicate that, regardless of loading mode, accumulation of microdamage in cancellous bone after monotonic loading to yield is influenced by donor characteristics other than traditional measures of microarchitecture, suggesting a possible role for tissue material properties.

The uniaxial tensile behavior of MarBN steel with a constant strain rate of 5 × 10-5 s-1 under various temperatures ranging from room temperature to 630 °C was analyzed. This study aimed to identify the effect of the temperature on the tensile behavior and to understand the microstructure deformation by electron backscatter diffraction. The tensile results showed that the yield and ultimate tensile strength decreased with increasing temperature. Serrated flow was observed from 430 °C to 630 °C. The electron backscatter diffraction analysis showed that the low-angle grain boundaries decreased at the medium deformation and increased at the maximum deformation. In contrast, they decreased with increasing temperatures. In addition, the number of voids increased with the increasing plastic strain. As the strain increased, the voids joined together, and the tiny cracks became larger and failed. Three mechanisms were responsible for the tensile deformation failure at various temperatures: grain rotation, the formation and rearrangement of low angle grain boundaries, and void nucleation and propagation. Finally, the formation of the low-angle grain boundaries and voids under different degrees of deformation is discussed.

The article presents the research results on the influence of variable shock conditions, such as temperature and water, thus reflecting shock atmospheric conditions during freezing and thawing, on the properties of samples produced using 3D printing technology from commonly used materials such as ABS, HIPS, PLA, and ASA. Understanding how different environmental conditions affect the quality, reliability, and durability of 3D prints can help to optimize the printing process and provide valuable information about their application possibilities. Tests related to the strength of the materials, such as static tensile testing, Charpy impact testing, and evaluation of structures, were carried out using a scanning electron microscope (SEM). Changes in chemical properties were measured by performing tests such as FTIR and TGA. Variations in chemical properties were measured by performing tests such as FTIR and TGA. One shock cycle lasting 7 days was sufficient to alter the properties of 3D prints, with the extent of changes depending on the material, as summarized in the test results.

The effect of reinforcements and thermal exposure on the tensile properties of aluminium AA 5083-silicon carbide (SiC)-fly ash composites were studied in the present work. The specimens were fabricated with varying wt.% of fly ash and silicon carbide and subjected to T6 thermal cycle conditions to enhance the properties through "precipitation hardening". The analyses of the microstructure and the elemental distribution were carried out using scanning electron microscopic (SEM) images and energy dispersive spectroscopy (EDS). The composite specimens thus subjected to thermal treatment exhibit uniform distribution of the reinforcements, and the energy dispersive spectrum exhibit the presence of Al, Si, Mg, O elements, along with the traces of few other elements. The effects of reinforcements and heat treatment on the tensile properties were investigated through a set of scientifically designed experimental trials. From the investigations, it is observed that the tensile and yield strength increases up to 160 °C, beyond which there is a slight reduction in the tensile and yield strength with an increase in temperature (i.e., 200 °C). Additionally, the % elongation of the composites decreases substantially with the inclusion of the reinforcements and thermal exposure, leading to an increase in stiffness and elastic modulus of the specimens. The improvement in the strength and elastic modulus of the composites is attributed to a number of factors, i.e., the diffusion mechanism, composition of the reinforcements, heat treatment temperatures, and grain refinement. Further, the optimisation studies and ANN modelling validated the experimental outcomes and provided the training models for the test data with the correlation coefficients for interpolating the results for different sets of parameters, thereby facilitating the fabrication of hybrid composite components for various automotive and aerospace applications.

The changes in the mechanical integrity of the cervix during pregnancy have implications for a successful delivery. Cervical collagens are known to remodel extensively in mice with progressing gestation leading to a soft cervix at term. During this process, mature crosslinked collagens are hypothesized to be replaced with immature less crosslinked collagens to facilitate cervical softening and ripening. To determine the mechanical role of collagen crosslinks during normal mouse cervical remodeling, tensile load-to-break tests were conducted for the following time points: nonpregnant (NP), gestation day (d) 6, 12, 15, 18 and 24 hr postpartum (PP) of the 19-day gestation period. Immature crosslinks (HLNL and DHLNL) and mature crosslinks (DPD and PYD) were measured using ultra performance liquid chromatography-electrospray ionization tandem mass spectrometry (UPLC-ESI-MS/MS). There were no significant changes in the total immature crosslink density (HLNL+DHLNL mol per collagen mol) throughout normal mouse gestation (range: 0.31-0.49). Total mature crosslink density (PYD+DPD mol per collagen mol) decreased significantly in early softening from d6 to d15 (d6: 0.17, d12: 0.097, d15: 0.026) and did not decrease with further gestation. The maturity ratio (total mature to total immature crosslinks) significantly decreased in early softening from d6 to d15 (d6: 0.2, d15: 0.074). All of the measured crosslinks correlated significantly with a measure of tissue stiffness and strength, with the exception of the immature crosslink HLNL. This data provides quantitative evidence to support the hypothesis that as mature crosslinked collagens decline, they are replaced by immature collagens to facilitate increased tissue compliance in the early softening period from d6 to d15.

Magnesium alloys have gained great attention as biodegradable materials for stent applications. Cardiovascular stents are continuously exposed to different types of mechanical loadings simultaneously during service, including tensile, compressive and fluid shear stress. In this study, the in vitro degradation of WE43 wires was investigated under combined effect of tensile loading and fluid shear stress and compared with that experienced an individual loading condition. For the individual mechanical loading treatment, the degradation of magnesium wires was more severely affected by tensile loading than fluid shear stress. Under tensile loading, magnesium wires showed faster increment of corrosion rates, loss of mechanical properties and localized corrosion morphology with the increasing tensile loadings. With the combined stress, smaller variation of the corrosion rates as well as the slower strength degeneration was shown with increasing stress levels, in comparison with the individual treatment of tensile loading. This study could help to understand the effect of complex stress condition on the corrosion of magnesium for the optimization of biodegradable magnesium stents.

Tensile property was one important index of mechanical properties of ANSI 304 stainless steel laser weldments subjected to cavitation erosion (CE). Laser shock processing (LSP) was utilized to strengthen the CE resistance, and the tensile property and fracture morphology were analyzed through three replicated experiment times. Results showed tensile process of treated weldments was composed of elastic deformation, plastic deformation, and fracture. The elastic limit, elastic modulus, elongation, area reduction, and ultimate tensile strength of tensile sample after CE were higher in view of LSP. In the fracture surface, the fiber zone, radiation zone and shear lip zone were generated, and those were more obvious through LSP. The number and size of pores in the fracture surface were smaller, and the fracture surface was smoother and more uniform. The dimples were elongated along the unified direction due to effects of LSP, and the elongated direction was in agreement with the crack propagation direction. Their distribution and shape were uniform with deeper depth. It could be reflected that the tensile property was improved by LSP and the CE resistance was also enhanced.

Introduction: The knee meniscus distributes and dampens mechanical loads. It is composed of water (∼70%) and a porous fibrous matrix (∼30%) with a central core that is reinforced by circumferential collagen fibers enclosed by mesh-like superficial tibial and femoral layers. Daily loading activities produce mechanical tensile loads which are transferred through and dissipated by the meniscus. Therefore, the objective of this study was to measure how tensile mechanical properties and extent of energy dissipation vary by tension direction, meniscal layer, and water content. Methods: The central regions of porcine meniscal pairs (n = 8) were cut into tensile samples (4.7 mm length, 2.1 mm width, and 0.356 mm thickness) from core, femoral and tibial components. Core samples were prepared parallel (circumferential) and perpendicular (radial) to the fibers. Tensile testing consisted of frequency sweeps (0.01-1Hz) followed by quasi-static loading to failure. Dynamic testing yielded energy dissipation (ED), complex modulus (E*), and phase shift (δ) while quasi-static tests yielded Young's Modulus (E), ultimate tensile strength (UTS), and strain at UTS (εUTS). To investigate how ED is influenced by the specific mechanical parameters, linear regressions were performed. Correlations between sample water content (φw) and mechanical properties were investigated. A total of 64 samples were evaluated. Results: Dynamic tests showed that increasing loading frequency significantly reduced ED (p < 0.05). Circumferential samples had higher ED, E*, E, and UTS than radial ones (p < 0.001). Stiffness was highly correlated with ED (R2 > 0.75, p < 0.01). No differences were found between superficial and circumferential core layers. ED, E*, E, and UTS trended negatively with φw (p < 0.05). Discussion: Energy dissipation, stiffness, and strength are highly dependent on loading direction. A significant amount of energy dissipation may be associated with time-dependent reorganization of matrix fibers. This is the first study to analyze the tensile dynamic properties and energy dissipation of the meniscus surface layers. Results provide new insights on the mechanics and function of meniscal tissue.

In this study, we have investigated the relationship between the spherulitic morphology and the dynamic tensile response of polyurethane reinforced with Halloysite nanotubes (HNTs). The polyurethane prepolymer is partially silane end-capped and filled with only 0.8 wt.% of acid-treated Halloysite nanotubes. The resultant nanocomposite material presents a 35% higher spall strength compared to the neat polyurethane and 21% higher fracture toughness. We show evidence that the HNTs are not the toughening phase in the nanocomposite, but rather it is their influence on the resultant spherulitic structures which alters the polymer microstructure and leads to a tougher dynamic response. Microstructural characterization is performed via Scanning Electron Microscopy, Atomic Force Microscopy and Field Emission Scanning Electron Microscopy, and crystallinity examination via X-ray diffraction. The spherulitic structures present a brittle fracture character, while the interspherulitic regions are more ductile and show large deformation. The nanocomposite presents a finer and more rigid spherulitic structure, and a more energy dissipative fracture mechanism characterized by a rougher fracture surface with highly deformed interspherulitic regions.

Fire is one of the most unfavorable conditions that cement-based composites can face during their service lives. The uniaxial tensile and flexural tensile properties of the steel-polyvinyl alcohol fiber-calcium carbonate whisker (CW) multi-scale fiber reinforced cement matrix composites (MSFRCs) under high temperatures are studied, including strength, deformation capacity, energy dissipation capacity, and its ability to be assessed through the empirical calculation method. The study showed that with the increase of the treatment temperature, the MSFRC residual bending strength, bending toughness, and tensile strength decreased overall, but the decline was slow at 600 °C. The peak flexural deflection and peak tensile strain of MSFRC first reduced and then increased with the increase of the temperature. As the temperature increased, the nominal stiffness of MSFRC bending and straight gradually reduced, and the rate of decline was faster than that of its strength. However, the uniaxial tensile properties were more sensitive to the temperature and degraded more rapidly. A quantitative relationship was established between MSFRC residual bending, tensile strength, and temperature. A comparison with existing research results shows that MSFRC has achieved an ideal effect of high temperature resistance. The multi-scale hybrid fiber system significantly alleviates the deterioration of cement-based composite's mechanical properties under high temperatures. With the help of an optical microscope and scanning electron microscope (SEM), the high temperature influence mechanism on the uniaxial tensile and flexural properties of MSFRC was revealed.

The growing demand for plant fiber-reinforced composites offers new opportunities to compete against glass fiber (GF)-reinforced composites, but their performance must be assessed, revised, and improved as much as possible. This work reports on the production and the flexural strength of composites from polypropylene (PP) and hemp strands (20-50 wt.%), using maleic anhydride-grafted PP (MAPP) as a compatibilizer. A computational assessment of the reaction between cellulose and MAPP suggested the formation of only one ester bond per maleic anhydride unit as the most stable product. We determined the most favorable MAPP dosage to be 0.06 g per gram of fiber. The maximum enhancement in flexural strength that was attained with this proportion of MAPP was 148%, corresponding to the maximum fiber load. The modified rule of mixtures and the assumption of similar coupling factors for tensile and flexural strength allowed us to estimate the intrinsic flexural strength of hemp strands as 953 ± 116 MPa. While falling short of the values for sized GF (2415 MPa), the reinforcement efficiency parameter of the natural fibers (0.209) was found to be higher than that of GF (0.045).

For years, the chemical injection process has aided construction works by increasing the strength and water-sealing efficiency of sandy soil. Despite its growing popularity in projects, such as seismic strengthening and liquefaction mitigation, a unified understanding of how chemically treated soil develops its strength, especially under static conditions, remains elusive. Some studies have proposed that strength is derived from the tensile effects of dilatancy, where shearing of the sandy soil causes expansion, creating tension in the interstitial hydrogel and resulting in negative pressure that consolidates the soil particles. Other studies, however, attribute this strength development to the volumetric shrinkage of the hydrogel, which the authors argue confines and compresses the sandy soil particles. Challenges are encountered with this theory, particularly with respect to the consistency of the volumetric shrinkage measurements and the timing of these measurements in relation to changes in soil strength. The aim of the current research is to shed light on this mechanism by using consolidation drainage triaxial compression (CD) tests to measure the cohesive strength and internal friction angle of chemically enhanced soil. By eliminating the dilatancy-induced negative pressure effects and coupling this with an analysis of the molecular structure of the hydrogel, the present study provides an in-depth look at the strength development mechanism and its durability. This holistic approach not only fills in the existing gaps in the understanding of this mechanism, but also paves the way for optimized construction techniques.